Gas Lift

Day One:

Course Introduction

Welcome remarks. Introduction of the instructor and participants.

Presentation of the course content. Participants’ expectations are carefully noted. General course rules and the class and break schedule are established. Initial exam. (*Each participant’s academic level and experience, as well as their performance on the initial exam, are used to determine the best teaching strategies for the course.)

General Aspects of the Gas Lift Method: General definitions for the applications of the method. Classification of the different subtypes of the method.

Advantages and disadvantages of gas lift. Properties of Gases: Equation of state for ideal and real gases. Reduced and pseudo-reduced properties.

Calculation of the compressibility factor for pure gases and mixtures of different gases. Dalton’s and Amagat’s Laws. Calculation of the specific gravity of a gas mixture.

Determination of the partial pressure of a component in a gas mixture.

For a gas or gas mixture, calculation of: Viscosity, water vapor content, hydrate formation, dew point curve, and specific heat ratio. In-class exercises.

Properties of liquids: Specific gravity of crude oil. Gas-oil ratio in solution, gas-water ratio in solution, formation volume factors, liquid viscosities, bubble point pressure, liquid density at in-situ conditions, liquid flow rates at in-situ conditions derived from flow rates at standard conditions. Influx pressure curve (IPR) equations: Darcy, Vogel, John-Blount-Glaze, Fetckovich.

In-class exercises.

Gradients: Gas gradients under static conditions, gas gradients with friction, liquid gradients (single-phase and multi-phase flow). In-class exercises.

 

Day Two:

Determining the Injection Point Depth:

Assuming constant or variable wellhead pressure.

Using variable injection flow rate equilibrium curves.

Using commercial simulators to determine the injection point depth and perform various calculations:

Injection point, liquid and gas injection production required when the injection pressure is sufficient to reach the maximum allowable injection depth.

Complete analysis of the production capacity of producing wells using gas lift.

Calculation of pressure and temperature profiles along the production tubing.

Nodal analysis with commonly applied sensitivity variables in gas lift, used to determine the production tubing size, among other design and diagnostic parameters.

Determining the required liquid and gas injection flow rates for a given set of injection, wellhead, and reservoir pressures.

Calculating the required injection point depth using the concept of equilibrium curves with constant injection flow rate.

Managing uncertainties in the well’s actual production capacity (bracketing).

Performance curves showing the effects of:

API grade of the crude oil, production tubing diameter, water cut, formation gas-oil ratio, reservoir pressure, productivity index, production manifold or separator pressure, injection point depth, and flow line diameter.

Surface and subsurface equipment for gas lift:

Different types of gas lift valves:

Injection pressure operated (IPO), production pressure operated (PPO), with chokes upstream or downstream of the seat, conventional valves (retrievable by tubing), valves for use with coiled tubing or packoff completions, among others.

Different types of locks and their operating principles for securing the valves to the lift mandrel (points to consider when selecting them).

Wireline Mandrels for:

Standard operations, annular production, accumulation chambers, and parallel and independent injection tubing.

Packoff mandrels, conventional mandrels (for tubing-retrievable valves), concentric mandrels, and mandrels with more than one pocket.

Subsurface and surface wireline systems.

Single-tube completions.

Double-tube completions: a) concentric or b) parallel tubing.

Completions recommended when gas lift is used as an alternate method in electric submersible pump (ESP) completions.

 

Day Three:

 

Mechanics of Gas Lift Valves:

Force balance equation and determination of calibration pressure for:

Nitrogen-charged IPO valves calibrated by opening pressure.

Spring-loaded IPO valves calibrated by opening and closing pressures.

Nitrogen-charged PPO valves.

Spring-loaded PPO valves calibrated by opening and closing pressures.

Determination of dome pressure (at workshop temperature from the pressure at operating temperature, or vice versa) using the API method or the approximate alternative method.

Workshop procedure for determining the bellows area to be used in valve mechanics calculations.

In-class exercises.

Gas flow through subsurface valves and orifices:

Deviation from the Thornhill-Craver equation applied to gas lift valves.

Dynamic behavior of gas lift valves: orifice, throttled, and transition flow.

Dynamic models of gas lift valves:

Models developed by: Decker, Hepguler, Sagar, Cordero, Escalante, Bertovic, Faustinelli, and Hernández.

Gas flow in gas lift valves with downstream and upstream chokes.

In-class exercises.

 

Day Four:

Design of continuous gas lift:

Discharge process.

Iterative design procedure using equilibrium curves with constant gas injection.

Mandrel spacing for:

 

IPO valves:

Sequentially lowering the opening pressure.

Sequentially lowering the closing pressure.

Max-min method.

IPO valves with upstream chokes.

IPO valves in wells with unknown production (exploratory).

PPO valves.

Calculation of the gas injection flow rate required for each discharge valve.

Determination of the discharge liquid flow rate.

Discharge valve temperature.

Discharge valve seat diameter and operating point.

Theory of optimization for dual wells.

Design of gas lift systems for dual wells.

Redesign techniques.

Verification of design stability.

Use of dynamic models for design verification and accurate calculation of the required gas volume and actual discharge time, as well as for predicting instabilities in the final operation or during discharge (caused by valve interference).

Analytical techniques for diagnosing continuous gas lift systems:

Difficulties typically encountered during the different phases of analysis and diagnosis of wells with continuous gas lift.

Causes of failures and efficiency losses in gas lift systems.

Diagnostic methodology for:

Wells that do not accept gas lift (the injection rate becomes zero).

A single injection point below the static fluid level in the well.

 

Calculation of valve opening and closing pressures under operating conditions based on workshop calibration data.

Wells circulating injection gas without liquid production.

Multiple injection points.

Inability to transfer the injection point to the next discharge valve.

Operational diagnostic techniques (field operations):

Communication test and alternate test.

Subsurface pressure and temperature logging techniques (conventional logs and continuous logs with high-precision, high-response-time sensors).

Acoustic logs.

Determination of the depth of the injection point(s) by injecting CO2 gas pulses.

Real-time measurements of downhole pressure and temperature.

Practical determination of the actual liquid level and bottomhole depth.

Temperature distribution along the well depth using fiber optic cables.

Measurement of liquid level patterns in the well test separator.

Measurement of liquid production patterns at the outlet of the well test separator.

Identification of gas injection control valve failures using gas gauge discs (or trend curves for electronic measurement and monitoring).

Interpretation of production and injection pressure variations at the wellhead (using pressure discs or reading trend curves in automated wells).

Real-world examples of well diagnostics.

Recent technological solutions in digital oil fields.

Use of computer programs that simulate dynamic conditions (transient states) of well production.

 

Day Five:

 

Well Design for Intermittent Gas Lift:

General guide on fundamental aspects for implementing intermittent lift.

Types of well architecture for intermittent gas lift.

Description of the parts and operation of different types of pilot valves.

Milano dynamic model for the dynamic behavior of pilot valves.

Injection control using surface chokes. Injection control using automatic surface injection controllers.

Design of wells with a single production tubing:

Design for surface injection control using chokes: calculation of optimal cycle time, gas required per cycle from the energy balance equation, determination of the valve closing pressure from a mass balance of the lift gas.

Design for surface injection control using controllers.

Mechanistic models (fundamentals of the ISIS software).

Design for accumulation chambers, simple accumulators, insertable accumulators, and gas pumps.

Diagnosis of wells in intermittent gas lift:

Identification of wells that are actually producing intermittently.

Common difficulties encountered during diagnosis.

Wells that should not be analyzed as intermittent.

Analytical techniques for single-point injection.

Diagnosis of wells with damaged downhole valves.

Tube-annular communication.

Pressure and temperature logs for intermittent wells:

Procedure and analysis of logs to determine the injection point. Procedure and analysis of logs for wells with a known injection point.

Examples of logs in actual wells (simple completions and those with accumulation chambers).

Acoustic logs (operational procedure and analysis).

Use of fiber optics to measure temperature distribution along the wellbore depth.

Analysis of pressure disks or trend curves.

Examples of real-world diagnoses.

Course closing

Final technical remarks.

Final exam (including open discussion).

Student evaluation of the course (instructor performance and effectiveness, relevance of the topics presented, audiovisual and reading materials, classroom facilities, etc.).

Issuance of attendance certificates.

Closing remarks.

 

14 December 2026

Ends: 18 December 2026

40 Hours

Abu Dhabi

USD 4950

Production and Facilities

Rated 4.5 out of 5

Contact

Registration to the course

Request in company